Camp Moto has a nice pool, approx. 12,500 gallons, supported by a poorly designed sand filtration system. We had a problem when we first moved in that required new sand in the filter. I believe the sand used was construction sand and not filtration sand, because we've had problems ever since, even if the chemicals are in balance and the filter runs several hours a day.
Two months ago the pump motor froze and it took two weeks to finally get it repaired and reinstalled. In that time we had a major algae bloom that even dumping gallons of chlorine and algae killer wouldn't kill without circulation.
Since then it's been hell trying to get the water clean and algae gone. The filter would not remove the algae because the algae particles are much too small. Sweeping and vacuuming just made the water cloudy, and when the pump was turned off for a while, a layer of yellow/brown slime would lay on every horizontal surface. Even vacuuming to waste had limited effectiveness.
Research led me to a product called SlimeBag which is a 7"x32" 1micron depth filter that attaches to the water outlets in the pool with specialized PVC fittings. It is suggested that half the outlets have one of these bags. The cost of four is around $300.
YIKES!
But let me state that I have no doubt SlimeBags, a trademarked product, is a quality, effective product. But I'm just too cheap to spend that kind of money without figuring out another way.
So I decided to go the DIY route.
I purchased 5 #2 1 micron 7" x 32" polyester felt diesel fuel filter bags from DudaDiesel on Ebay, under $40 shipped to my Miami freight forwarder.
I ordered 10 2.25-3.25" SS hose clamps for $8. By the time all is shipped to the DR, I'll have spent $55.
Rather than fuss with PVC adapters, I'll simply cut the ring from the top of each bag, and cut tabs 1.5" from the top. I'll then simply neatly bunch the bag around each of return fittings that stick out about 5/8-3/4" into the pool, and secure them tightly with the SS hose clamps. I'll then shut off the other 4 returns.
So for under $55, I'll have efficient "slime" filters on 4 returns, with on spare, for $15 less than the cost of one Slime Bag.
All the materials came in. Here are the parts I used:
Filter bag, 2.5"-3.5" SS hose clamp, scissors, razor knife, screwdriver and bottle (for shaping.)
The filter bags are a quality unit and much tougher, substantial, well-constructed and thick than I expected.
First I removed the strap & metal ring from the bag:
I cut slices at the lip. Note: I found more cuts and removing some tabs works best. Pics later.)
The hose clamps were fully opened, and I folded the filter to slide the clamp to the slits on the top:
The bottle is about the same diameter as the outlets from the filter. I used it to form a round opening in the bunched filter mouth. This is kinda clunky at first, but you figure it out quickly:
I'm ready to install the bags. Sorry, no pics. But the key is to open the bag enough to get it over an outlet and firmly tighten the hose clamp onto the outlet. This is easier said than done, and took a few tries to finally figure it out. But it worked. One secret is to make cut tabs and cut off half. This prevents bunching of the thick material, because you're taking thick fabric made into a 7" diameter opening down to 2.5-3", so there can be a lot of bunching. You can see this in later pictures.
I put 3 bags on one the 4 outlet banks, and shut off the other bank, so 75% the water would flow into the 3 bags. MISTAKE. When I turned on the pump, I could see a brown cloud coming from the filter bags after they caught some algae. Shutting off half the outlets created too much pressure and the bag would not contain the algae. So I made a 4th bag, and put it on the one outlet on the other bank that protruded out enough to attach, and opened both banks. When I turned the pump back on...*voila!* Success! The bags filled and captured the gunk.
Every day the pool got cleaner, there was less algae and the bags were turning brown. But then no more progress, and I noticed the bags were hard from internal pressure. Then one blew off. I captured it and looked inside: completely covered with gunk.
(Note the tabs; much easier.)
So I had my guy, Junior (and his son helper), take all the bags off and clean them:
NOTE: this is easy. I noticed with the SlimeBags cleaning is somewhat problematic. But we took the top ring off, turned then inside out, put it over a pole and sprayed it with water until clean.
Note the tabs again.
4 cleaned, and back into the pool!
The pool became MUCH cleaner, and the clean bags began to turn brown again after 10 days. I noticed water escaping from around the hose clamp on one, so I figured the pressure was high and the bag no longer filtering, so out they came. When I would unattach a bag and lift it from the pool, little water escaped/filtered through since the bag had become occluded.
Dirty bag, part two. They aren't as bad as the first time, but still very dirty:
Yuck. This has been circulating in my pool:
Second cleaning was much easier. This time I put then against a chain link fence, used barbed wire to keep it from falling, and used my pressure sprayer. Good choice, clean again (this is on the pole for a picture):
Back in the pool:
I suspect there will be at least one more cleaning before ALL the dead algae is gone, but I have no doubt the problem will be solved.
I bought 5 bags in a lot from Duda, and I am glad I did. I now put water into the pool from the cistern (fed by the local water company) through the remaining bag.
Why is this necessary? This is from one filling:
In the past that water, unfiltered, went into the pool.
Bottom Line:
All-in-all I am quite pleased with both the cost and results. I also think this offers one distinct advantage over the actual SlimeBag: ease of cleaning. the SlimeBag, I recall, has a small fitting on the bag that makes cleaning difficult. I just turn the bag inside out like a pair of socks for cleaning.
Two months ago the pump motor froze and it took two weeks to finally get it repaired and reinstalled. In that time we had a major algae bloom that even dumping gallons of chlorine and algae killer wouldn't kill without circulation.
Since then it's been hell trying to get the water clean and algae gone. The filter would not remove the algae because the algae particles are much too small. Sweeping and vacuuming just made the water cloudy, and when the pump was turned off for a while, a layer of yellow/brown slime would lay on every horizontal surface. Even vacuuming to waste had limited effectiveness.
Research led me to a product called SlimeBag which is a 7"x32" 1micron depth filter that attaches to the water outlets in the pool with specialized PVC fittings. It is suggested that half the outlets have one of these bags. The cost of four is around $300.
YIKES!
But let me state that I have no doubt SlimeBags, a trademarked product, is a quality, effective product. But I'm just too cheap to spend that kind of money without figuring out another way.
So I decided to go the DIY route.
I purchased 5 #2 1 micron 7" x 32" polyester felt diesel fuel filter bags from DudaDiesel on Ebay, under $40 shipped to my Miami freight forwarder.
I ordered 10 2.25-3.25" SS hose clamps for $8. By the time all is shipped to the DR, I'll have spent $55.
Rather than fuss with PVC adapters, I'll simply cut the ring from the top of each bag, and cut tabs 1.5" from the top. I'll then simply neatly bunch the bag around each of return fittings that stick out about 5/8-3/4" into the pool, and secure them tightly with the SS hose clamps. I'll then shut off the other 4 returns.
So for under $55, I'll have efficient "slime" filters on 4 returns, with on spare, for $15 less than the cost of one Slime Bag.
All the materials came in. Here are the parts I used:
Filter bag, 2.5"-3.5" SS hose clamp, scissors, razor knife, screwdriver and bottle (for shaping.)
The filter bags are a quality unit and much tougher, substantial, well-constructed and thick than I expected.
First I removed the strap & metal ring from the bag:
I cut slices at the lip. Note: I found more cuts and removing some tabs works best. Pics later.)
The hose clamps were fully opened, and I folded the filter to slide the clamp to the slits on the top:
The bottle is about the same diameter as the outlets from the filter. I used it to form a round opening in the bunched filter mouth. This is kinda clunky at first, but you figure it out quickly:
I'm ready to install the bags. Sorry, no pics. But the key is to open the bag enough to get it over an outlet and firmly tighten the hose clamp onto the outlet. This is easier said than done, and took a few tries to finally figure it out. But it worked. One secret is to make cut tabs and cut off half. This prevents bunching of the thick material, because you're taking thick fabric made into a 7" diameter opening down to 2.5-3", so there can be a lot of bunching. You can see this in later pictures.
I put 3 bags on one the 4 outlet banks, and shut off the other bank, so 75% the water would flow into the 3 bags. MISTAKE. When I turned on the pump, I could see a brown cloud coming from the filter bags after they caught some algae. Shutting off half the outlets created too much pressure and the bag would not contain the algae. So I made a 4th bag, and put it on the one outlet on the other bank that protruded out enough to attach, and opened both banks. When I turned the pump back on...*voila!* Success! The bags filled and captured the gunk.
Every day the pool got cleaner, there was less algae and the bags were turning brown. But then no more progress, and I noticed the bags were hard from internal pressure. Then one blew off. I captured it and looked inside: completely covered with gunk.
(Note the tabs; much easier.)
So I had my guy, Junior (and his son helper), take all the bags off and clean them:
NOTE: this is easy. I noticed with the SlimeBags cleaning is somewhat problematic. But we took the top ring off, turned then inside out, put it over a pole and sprayed it with water until clean.
Note the tabs again.
4 cleaned, and back into the pool!
The pool became MUCH cleaner, and the clean bags began to turn brown again after 10 days. I noticed water escaping from around the hose clamp on one, so I figured the pressure was high and the bag no longer filtering, so out they came. When I would unattach a bag and lift it from the pool, little water escaped/filtered through since the bag had become occluded.
Dirty bag, part two. They aren't as bad as the first time, but still very dirty:
Yuck. This has been circulating in my pool:
Second cleaning was much easier. This time I put then against a chain link fence, used barbed wire to keep it from falling, and used my pressure sprayer. Good choice, clean again (this is on the pole for a picture):
Back in the pool:
I suspect there will be at least one more cleaning before ALL the dead algae is gone, but I have no doubt the problem will be solved.
I bought 5 bags in a lot from Duda, and I am glad I did. I now put water into the pool from the cistern (fed by the local water company) through the remaining bag.
Why is this necessary? This is from one filling:
In the past that water, unfiltered, went into the pool.
Bottom Line:
All-in-all I am quite pleased with both the cost and results. I also think this offers one distinct advantage over the actual SlimeBag: ease of cleaning. the SlimeBag, I recall, has a small fitting on the bag that makes cleaning difficult. I just turn the bag inside out like a pair of socks for cleaning.